Oxygen sensor recycling is one of the most important methods used by car owners to raise the efficiency of their engines. Air feelers are part of the exhaust system where they get exposed to many pollutants such as hydrocarbons, nitrogen oxides, and carbon oxides among others. These pollutants, coupled with frequent cooling and heating result to destruction of the air feeler. This article is a holistic account of how to recycle your air car feeler.
Engine coolant, fuel, and even oil contamination are some of the key causes that damage vehicle feelers. The destruction is advanced by accumulation of soot especially in the part made of ceramic. The impact of this, when compounded with low quality gasoline, lowers the engine effectiveness and demands for a replacement if not addressed fast.
Because air feelers work is assisting to maintain the right mixture of fuel and air in the exhaust, impurities have always been associated with lean or rich engine. Maintaining the air feeler will as a result assist to bring down the amount of gas used by your car. It is also associated with greater car engine efficiency.
Procuring new air feelers for a car can be very costly and make running the car unsustainable. After noticing problems with the air feeler, the best course of action is not considering to look for replacement, but seeking ways of salvaging it. It is however important for you to understand that the process of cleaning and salvaging the feeler is not easy and requires great care.
Since the sensor works at very high temperatures in the car exhaust system, the key contaminants are always blanketed by a thick layer of hardened carbon at the tip of all the feelers. Remember that this hardened layer will not be easily dissolved by any solvent. The most effective method of removing the carbon residue is using a strong blow torch to heat the tip. Hold the torch close to the tip and heat until it turns red hot before immersing quickly in water.
After the air feeler temperature goes down, pass strong steam of air to clean the tip. This will ensure that pollutant deposits on the feeler loosen and fall off. It is important to ensure you repeat the process of blowing the surface a couple of times until it looks as clean as new.
To remove contaminants resulting from oil and fuel, it is advisable to use CRC type of electronic cleaner. This cleanser is very effective and clears all the fuel related contaminants without leaving any residue. To avoid damaging the air feeler, it is important to avoid contacts of any air feeler with the cleaner nozzle.
The method of salvaging the feeler exposes the cleaners hands and other parts of the body to pollutants and dangerous chemicals. To protect yourself, it is advisable to use hand gloves when opening the exhaust, handling chemicals, and during the entire cleaning process. The eyes, ears, nose and mouth should further be protected using goggles, ear pads, and masks that prevent inhalation of dangerous pollutants and chemicals. Salvaging your air feeler is a great method of reducing the cost of maintaining a car and promoting its efficiency.
Engine coolant, fuel, and even oil contamination are some of the key causes that damage vehicle feelers. The destruction is advanced by accumulation of soot especially in the part made of ceramic. The impact of this, when compounded with low quality gasoline, lowers the engine effectiveness and demands for a replacement if not addressed fast.
Because air feelers work is assisting to maintain the right mixture of fuel and air in the exhaust, impurities have always been associated with lean or rich engine. Maintaining the air feeler will as a result assist to bring down the amount of gas used by your car. It is also associated with greater car engine efficiency.
Procuring new air feelers for a car can be very costly and make running the car unsustainable. After noticing problems with the air feeler, the best course of action is not considering to look for replacement, but seeking ways of salvaging it. It is however important for you to understand that the process of cleaning and salvaging the feeler is not easy and requires great care.
Since the sensor works at very high temperatures in the car exhaust system, the key contaminants are always blanketed by a thick layer of hardened carbon at the tip of all the feelers. Remember that this hardened layer will not be easily dissolved by any solvent. The most effective method of removing the carbon residue is using a strong blow torch to heat the tip. Hold the torch close to the tip and heat until it turns red hot before immersing quickly in water.
After the air feeler temperature goes down, pass strong steam of air to clean the tip. This will ensure that pollutant deposits on the feeler loosen and fall off. It is important to ensure you repeat the process of blowing the surface a couple of times until it looks as clean as new.
To remove contaminants resulting from oil and fuel, it is advisable to use CRC type of electronic cleaner. This cleanser is very effective and clears all the fuel related contaminants without leaving any residue. To avoid damaging the air feeler, it is important to avoid contacts of any air feeler with the cleaner nozzle.
The method of salvaging the feeler exposes the cleaners hands and other parts of the body to pollutants and dangerous chemicals. To protect yourself, it is advisable to use hand gloves when opening the exhaust, handling chemicals, and during the entire cleaning process. The eyes, ears, nose and mouth should further be protected using goggles, ear pads, and masks that prevent inhalation of dangerous pollutants and chemicals. Salvaging your air feeler is a great method of reducing the cost of maintaining a car and promoting its efficiency.
About the Author:
You can visit www.pgmrecoverysystems.com for more helpful information about Info On Oxygen Sensor Recycling.
